The drill bit

ralph klimek Nov 2009

keywords:  repairing a fractured drill bit, method
abstract:  method for an add hoc repair of a shattered large drill bit suitable for home use, without precision machinery



The motivation for this simple project arose because I needed to drill many 5/8ths  holes in metal.  Many years ago I purchased a fragment of 5/8ths drill from a flea market. This fragment could just barely be held in a hand brace, but this was barely workable.  When I went to Bunnings to buy a 5/8ths reduced shank drill bit, they were about A$50  which costed more then the entire project.  I took a second look at my drill fragment to see what value I could add.

What it needed was a reduced shank, and to be really usefull as a drill the shank had to be collinear. It has to be usefull in my electric drill so that added extra requirements for collinearity and balance.  I had a good stock of 1/2inch steel shaft which could be welded to the drill fragment...but how to weld it so the whole thing was true ,colinear, and resonably well balanced.

Hold it in a lathe!  This would be the proper answere, except I dont have one and the prospect of ever being able to own one is getting somewhat remote.  What could I do that did not require a lathe?

The images show the drill bit being welded in a purpose built wooden jig. This primative arrangement was able to hold the drill bit and shaft with sufficient resilience and accuracy to permit this "new remanufactured" drill to be a success.

I do not have access to precision layout or machine tools.  Four bits of hardwood had to be drilled with a collinear hole, enlarged and mounted on a sturdy base...all while maintaining absolute collinearity.  The orientation of the string of holes did not really matter.

First I tried to lay things out by measurement , marking and cutting. Total failure.  Wood is not like metal, it has a mind of its own and wood will displace a penetrating drill bit laterally, so no matter how hard you try,  holes never really line up and remain true.

This describes a repeatable procedure .  The sequence must be exactly followed. Absolute Collinearity is what we are trying to create and preserve in an envoironment denied of precision.

procedure

Get 4 pieces of wood that have been resonably well dressed.  Number them and mark to preserve orientation. Clamp them all between heavy plates in a sturdy vice and drill one  1/2inch hole (in this case)  through the stack.  The direction of the hole is not that important. Immediately force through  a length of 1/2inch shaft and remove the skewered stack of blocks from the vise and space and place them on the mounting board. Do not remove the shaft ! The shaft is holding the alignment.

Now drill and screw the blocks to the mounting board.  Do not remove the 1/2inch shaft during this procedure or you will loose the alignment and you must start again with fresh material !

Remove the two blocks that will be holding the drill bit.  At this point  we still have perfect alignment because we drilled and screwed the blocks with the shaft in place, maintaining the alignment. Now drill these removed blocks out to the required size.  This part of the process may loose some of the precision, but we have two blocks, so on average  the alignment is preserved.

Remount the two enlarged hole blocks in their positions. Did you mark and number your blocks ?

With a grinder dress the end of your drill fragment with a nice bevelled edge ready for welding.

Force the  new shank and drill bit fragment into the jig.  If you have done all the above right they will be perfectly aligned.

Weld a small bead, turn the drill around and weld a small bead on exactly the other side. This is important . If you try to do the whole
extent of the weld, the thermal expansion forces will bend your drill like a banana.  

Now begin to fill the remaining seam with weld metal.

This procedure will set fire to the jig but that does not matter, the jig is disposable.

High speed tungsten steel drill metal  welds very well.  You might like to anneal the completed weld with a gas flame as the weld could be quite brittle. Mine welded very nicely to mild steel shaft.  Make sure that as far as humanely possible that there are no slag inclusions. This is a safety matter!


My repaired drill was used with success, luck even allowed it  to be nicely balanced. I still would not use it in a high powered drill press due to the risk of the weld fracturing under load, but it is perfectly suitable for hand held drill use in light material.





imgp4673-drillshaft.jpgimgp4675-drillshaft.jpg
imgp4674-drillshaft.jpgthumb.imgp4864-welded-drill.jpg
temporary wooden jiggingrepair completed





this project was brought to you by the welder-o-doom

homepage






page created Mon Nov 23 18:55:25 EST 2009;Fri Feb  5 18:16:58 EST 2010